Browning 1885 High Wall .45-70
Browning attempted to capture the look of the high-wall Winchester of a century ago. However, the Japanese folks who made this Browning decided to put a glassy finish on this historic-minded rifle, which didnt do it any good. Old Winchesters never had glassy-finish stocks, nor did they have buffed barrels that lost the sharp edges of the octagon. So right off the bat, this rifle didnt look right because of its glitzy finish. However, the profile and mechanism of the test rifle looked a lot like a High-Wall Winchester, and the rifle had some well-done features, according to Gun Tests magazine.
Browning used to offer a higher-priced Traditional Hunter version of this rifle, which had an oil-type finish. These were discontinued, but you may still be able to find one. Another Browning option was the BPCR, which stands for Black Powder Cartridge Rifle. These sold for nearly $1,800, and are also discontinued. They were offered in .40-65 and .45-70, and didnt sell very well.
This was no lightweight. Empty, the rifle weighed 8 pounds, which was a little closer to the 10.5-pound weight of a Sharps than a 7-pound Ruger was. Part of the extra weight of the Browning was in its 28-inch barrel, compared to the Rugers 22-incher.
Opening the 1885s action caused the hammer to be cocked as the action block moved downward. With the action closed, if the hammer were lowered slowly, it did not strike the firing pin, nor could it be moved by any means to make contact with the pin. However, a normal pull on the trigger would cause the cocked hammer to strike the firing pin and fire the rifle. This feature would be handy whenever you wanted to carry a loaded but uncocked rifle. In spite of that, the serrations on the hammer were not deep enough for testers.
The wood was extremely attractive, and both sides of the stock had the same grain pattern. The glassy stock finish tended to hide the woods great beauty under glaring hot spots. Some sort of dull oil-looking finish would have been far better than the very glossy finish applied. It appeared to be an epoxy finish because it was nearly unmarkable, extremely hard, filled the pores perfectly, and had a mirror-like surface. The forend wood matched the beautiful grain structure of the buttstock very well. Both pieces of wood had excellent checkering in five well-proportioned panels, three of them on the forend. There were QD sling swivel studs. The butt was padded with thick black rubber that was just as hard as that of the Ruger, if not harder.
The makers of this rifle should shoot it with some of the Buffalo Bore heavy loads, to see what its doing to its sales by putting these cast-iron buttplates on the otherwise very nice rifle. Anybody buying a .45-70 rifle in 2001 is going to shoot it with heavy loads, at least part of the time. The rifle was perfectly capable of handling loads that would drop an elephant. Manufacturers need to get wise to this, and put reasonable pads on their rifles. Surely any changes to pull length to fit individuals should be achieved with the use of a good recoil-absorbing pad.
The metal polish was, as already stated, somewhat overdone. The action flats were good and flat, with no polishing marks anywhere. The edges were just the right amount of sharp. Unfortunately, the octagonal barrel was a bit too well polished. All the flats of the barrel except the very top one were slightly rounded, and the sharp edges between flats were not sharp enough. The makers name and other information was stamped into the barrel flats, leaving slightly raised and unsightly lettering. The bluing was flawless. It was a rich, deep blue-black on all metal parts except the trigger, which was gold-plated, and the falling block itself, which was left white. The blocks polish was excellent, with no machining marks visible.
The trigger guard, which was also the action lever, had the Browning logo in gold inlaid into its bottom. The inletting was very good, though the forend appeared to be putting more pressure on the left side of the barrel than on the right. Metal fitting was outstanding throughout.
The action and barrel were tapped with holes for a scope base, and the holes filled with tiny screws. The rear sight was a buckhorn, adjustable for elevation by a sliding wedge, and for windage by drifting. The front sight was a square-sided blade which appeared to the eye as a thin flat-top post, adjustable for windage by drifting. One delightful effect of the half-moon cutout of the buckhorn sight was that the front blade, which appeared to older eyes as a blur when seen by itself, sharpened up perfectly when seen through the rear sight. The trigger pull was crisp and clean at 4 pounds, and testers looked forward to shooting this rifle.
At the range, the Browning was very gentlemanly in its manners. It had a distinctly different feel with its long barrel. The action worked very smoothly and well, and showed no problems with it at all. There was a small blade that could be turned either in the way, or out of the way of ejected shells, to make retrieving empties easier. Left that way, the ejected empties were easily found. Recoil with the hardest-kicking load, which seemed to be the 350-grain BB fodder, was nasty. The rifle also kicked up into the cheekbone, which hurt as much as, or more than, the bang on the shoulder. But as stated above, theres no need to shoot more than a few of these rounds from the bench. Fun is to be had with light handloads. The best 100-yard group with the test ammunition was 2.0 inches, fired with the 430-grain BB cast lead load, which went across the chronograph at 1,985 fps. Thats not too far behind a .458 Win. Mag.
Gun Tests Recommends: Browning Model 1885 High-Wall, $997. Buy It. Though Gun Tests didnt care for the shiny finish, the Browning was a well-made rifle that shot very well. With its long barrel and short forend, it had a look and feel more like an ancient rifle than others did. There were no problems with the Browning at all, other than testers didnt want to stop shooting it with lighter loads.